So many $1 wireless ICs have a powerful "SDR", but will never be documented due to certification/compiliance/export-control reasons. The projects listed here rightly limited the scope to RX-only but Espressif might be forced to "patch" this away if arbitrary TX too is possible (or starts making headlines). Hope it doesn't come to that, more cheap options for RF-to-bits is always welcome.
On a technical note, not much I can find about the signal quality. Phase noise, images, DC Offset, etc. Have to get my hands on one, ESP32-S31 seems promising.
It is legal for a person with an appropriate license, yes. But laws (in the US) about RF transmission differ from how many other laws are structured: We're only allowed to transmit what we have permission to transmit -- and by default, we're forbidden.
But right now, I've got an ESP32 WROOM module on a dev board sitting in my windowsill reporting some sensor values over wifi.
The WROOM itself is registered with the FCC[1]. If I stick to using the documented operation, then I have permission to use it in those documented ways. As a practical concept, I don't need a unique license to use it in the way that I am; I'm granted the ability to use it by Part 15 of the FCC rules.
And that's pretty great: The hardware was inexpensive to buy and very easy to find. I was able to spin this sensor up very quickly and get moving on the software side that deals with those readings. It has been a very rewarding little project with a fantastic cost:benefit ratio.
The fear being expressed here (which I don't necessarily subscribe to) is that things like this WROOM module will become less-available when/if methods to use it in undocumented ways are published and start becoming used.
As far as I follow the research process it's currently quite difficult to get all data (like the 80MSPS@10-Bit showcase on Reddit) to a computer without a FPGA+USB3.
With the new ESP32-S31 we most likely can extract the I/Q data over its new 1 GBit/s interface. Guessing something around 20-40MSPS should work.
These hack will most likely will be a revolution for 13cm ham radio. With the new 5GHz ESP32 modules most likely also for 5cm. As all Espressif components are WiFi-qualified we can expect a very very stable and robust radio.
I ordered a few and waiting for Ali to deliver them to my lab.
On a technical note, not much I can find about the signal quality. Phase noise, images, DC Offset, etc. Have to get my hands on one, ESP32-S31 seems promising.
The modems could be quite interesting as they are connected via PCIe which can eat a lot of bandwidth.
But they are very difficult (to almost impossible) to find if there isn't anything left in the firmware blob or device driver.
Why would they? It's perfectly legal to operate radio transmitters on any frequency you like, if you hold a suitable licence.
But right now, I've got an ESP32 WROOM module on a dev board sitting in my windowsill reporting some sensor values over wifi.
The WROOM itself is registered with the FCC[1]. If I stick to using the documented operation, then I have permission to use it in those documented ways. As a practical concept, I don't need a unique license to use it in the way that I am; I'm granted the ability to use it by Part 15 of the FCC rules.
And that's pretty great: The hardware was inexpensive to buy and very easy to find. I was able to spin this sensor up very quickly and get moving on the software side that deals with those readings. It has been a very rewarding little project with a fantastic cost:benefit ratio.
The fear being expressed here (which I don't necessarily subscribe to) is that things like this WROOM module will become less-available when/if methods to use it in undocumented ways are published and start becoming used.
[1]: https://fccid.io/2AC7Z-ESPWROOM32
With the new ESP32-S31 we most likely can extract the I/Q data over its new 1 GBit/s interface. Guessing something around 20-40MSPS should work.
These hack will most likely will be a revolution for 13cm ham radio. With the new 5GHz ESP32 modules most likely also for 5cm. As all Espressif components are WiFi-qualified we can expect a very very stable and robust radio.
I ordered a few and waiting for Ali to deliver them to my lab.
> However, the current prototype uses the FPGA to clock the ESP32, which results in poor phase noise.
Looks like this was solved five days ago:
https://github.com/h0m3us3r/eSpDR/commit/41a0ffe279119df942e...
SDR in this context is software defined radio.
So kind of like those TV USB sticks that you can adapt into proper SDRs?
I remember the Ettus devices to be much much more powerful.